Try this quiz to review material covered in class and test your knowledge. If you don't understand the questions or answers, please ask me about it, ideally in class, but any other way of asking me would be fine too.

Stan

 

Quiz Class One
# Question Answer
1 The 'thrusting' cut is a very common whittling technique. In order to not cut yourself while making a thrusting cut, what must you always remember? Always cut away from yourself.
2 How would you describe the behaviour or the action of the knife at the end of a thrusting cut? This is often what causes an injury during whittling when you don't remember the answer to the question above. In other words, when you injure yourself while whittling (if you injure yourself) what kind of movement is the knife exhibiting just as it cuts you? The knife jumps. A knife always jumps at the end of a thrusting cut. If you cut towards yourself during a thrusting cut, you could easily cut yourself. Always cut away from yourself when using the thrusting cut.

3 Why does the knife behave the way it does at the end of a thrusting cut? The knife jumps at the end of a thrusting cut because a thrusting cut is one in which the force of the knife is applied directly against the resistance of the wood, and once the cut is complete the wood resistance no longer holds the knife back, and so the momentum in the force of the knife carries forward in a jump, which is impossible to restrain in a controlled way. One likes to think and feel that the jump can be controlled, but the jump cannot be controlled. This is why the force of the cut, and therefore the direction of the jump, must always be directed away from yourself.
4 Since a thrusting cut, when used properly, can do little more than make a pointed stick, what other techniques or methods can be used to safely cut more complex forms, such as a notch near the end of a stick?

More complex forms, such as a notch near the end of a stick, will require cuts that travel in a direction towards yourself. A levering, pivoting, or clenching technique, when properly done, will allow a controlled cut in a direction towards yourself without the possibility of a knife jump, which could cause an injury.
5 For the purposes of whittling, how does a freshly-cut tree branch differ from a stick of dry lumber sawn from a board? A freshly-cut tree branch is wetter, softer, less brittle, more flexible, more fragrant and colourful, stickier (sometimes), and cheaper. The form is roundish and irregular, sometimes with branches and leaf scars, arrived at by the growth process of the tree. The grain of the branch follows the form of the branch exactly - also reflecting the growth of the wood fibres that become the branch. The annual rings of the branch, and the branch centre (or pith) can be seen in a cross-sectional view of the branch (counting the rings gives the age of the branch).

A stick of dry lumber cut from a board is drier, harder, more brittle, less flexible, not as fragrant or colourful and is more expensive. A cross-sectional view will show some of the annual rings (but not all of them) and almost never shows the centre of the tree or branch. The straight and rectangular form of the stick tells you nothing about the grain direction of the wood in the stick except that it runs along the length of the stick, more-or-less.

6 How can you tell the difference between a branch of Chinese Sumac and a branch of Manitoba Maple, and how would working with one be different than the other?  
7 How can you easily and usually tell the difference between Hardwood trees and Softwood trees? What are the general characteristics of each?  
8 What do the following terms mean: Deciduous, Coniferous, Evergreen.  
9 What is the difference between working with a wood that is hard (like oak) and a wood that is soft (like cedar)? What are the benefits and drawbacks associated to working with each?  
10 What are taugua nuts and why are they useful?  
11

When making a form in wood, such as the figure of a man with outstretched arms, what is it about the arms of the man that explains why they are likely to be weak and break?

man with outstretched arms

 
12 In making the wooden man with arms outstretched, what strategies can be employed to make the arms stronger and less likely to break?